python-escpos/doc/user/usage.rst

*****
Usage
*****

Define your printer
-------------------

USB printer
^^^^^^^^^^^

Before start creating your Python ESC/POS printer instance, you must see
at your system for the printer parameters. This is done with the 'lsusb'
command.

First run the command to look for the "Vendor ID" and "Product ID", then
write down the values, these values are displayed just before the name
of the device with the following format:

::

    xxxx:xxxx

Example:

::

    # lsusb
    Bus 002 Device 001: ID 04b8:0202 Epson ...

Write down the the values in question, then issue the following command
so you can get the "Interface" number and "End Point"

::

    # lsusb -vvv -d xxxx:xxxx | grep iInterface
        iInterface              0
    # lsusb -vvv -d xxxx:xxxx | grep bEndpointAddress | grep OUT
          bEndpointAddress     0x01  EP 1 OUT

The first command will yields the "Interface" number that must be handy
to have and the second yields the "Output Endpoint" address.

**USB Printer initialization**

::

    Epson = printer.Usb(0x04b8,0x0202)

By default the "Interface" number is "0" and the "Output Endpoint"
address is "0x01", if you have other values then you can define with
your instance. So, assuming that we have another printer where in\_ep is
on 0x81 and out\_ep=0x02, then the printer definition should looks like:

**Generic USB Printer initialization**

::

    Generic = printer.Usb(0x1a2b,0x1a2b,0,0x81,0x02)

Network printer
^^^^^^^^^^^^^^^

You only need the IP of your printer, either because it is getting its
IP by DHCP or you set it manually.

**Network Printer initialization**

::

    Epson = printer.Network("192.168.1.99")

Serial printer
^^^^^^^^^^^^^^

Must of the default values set by the DIP switches for the serial
printers, have been set as default on the serial printer class, so the
only thing you need to know is which serial port the printer is hooked
up.

**Serial printer initialization**

::

    Epson = printer.Serial("/dev/tty0")

Other printers
^^^^^^^^^^^^^^

Some printers under /dev can't be used or initialized with any of the
methods described above. Usually, those are printers used by printcap,
however, if you know the device name, you could try the initialize
passing the device node name.

::

    Epson = printer.File("/dev/usb/lp1")

The default is "/dev/usb/lp0", so if the printer is located on that
node, then you don't necessary need to pass the node name.

Define your instance
--------------------

The following example demonstrate how to initialize the Epson TM-TI88IV
on USB interface

::

    from escpos import *
    """ Seiko Epson Corp. Receipt Printer M129 Definitions (EPSON TM-T88IV) """
    Epson = printer.Usb(0x04b8,0x0202)
    # Print text
    Epson.text("Hello World\n")
    # Print image
    Epson.image("logo.gif")
    # Print QR Code
    Epson.qr("You can readme from your smartphone")
    # Print barcode
    Epson.barcode('1324354657687','EAN13',64,2,'','')
    # Cut paper
    Epson.cut()

Configuration File
------------------

You can create a configuration file for python-escpos. This will
allow you to use the CLI, and skip some setup when using the library
programically.

The default configuration file is named ``config.yaml``. It's in the YAML
format. For windows it is probably at::

    %appdata%/python-escpos/config.yaml

And for linux::

        $HOME/.config/python-escpos/config.yaml

If you aren't sure, run::

        from escpos import config
        c = config.Config()
        c.load()

If it can't find the configuration file in the default location, it will tell
you where it's looking. You can always pass a path or a list of paths to
search to the ``load()`` method.


To load the configured pritner, run::

        from escpos import config
        c = config.Config()
        printer = c.printer()


The printer section
^^^^^^^^^^^^^^^^^^^

The ``printer`` configuration section defines a default printer to create.

The only required paramter is ``type``. The value of this should be one of the
printers defined in :doc:`/user/printers`.

The rest of the parameters are whatever you want to pass to the printer.

An example file printer::

        printer:
                type: File
                devfile: /dev/someprinter

And for a network printer::

        printer:
                type: network
                host: 127.0.0.1
                port: 9000

Advanced Usage: Print from binary blob
--------------------------------------

Imagine you have a file with ESC/POS-commands in binary form. This could be useful for testing capabilities of your
printer with a known working combination of commands.
You can print this data with the following code, using the standard methods of python-escpos. (This is an
advantage of the fact that `_raw()` accepts binary strings.)

::

    from escpos import printer
    p = printer.Serial()  # adapt this to your printer model

    file = open("binary-blob.bin", "rb")  # read in the file containing your commands in binary-mode
    data = file.read()
    file.close()

    p._raw(data)

That's all, the printer should then print your data. You can also use this technique to let others reproduce an issue
that you have found. (Just "print" your commands to a File-printer on your local filesystem.)
However, please keep in mind, that often it is easier and better to just supply the code that you are using.

Here you can download an example, that will print a set of common barcodes:

    * :download:`barcode.bin </download/barcode.bin>` by `@mike42 <https://github.com/mike42>`_

How to update your code for USB printers
----------------------------------------

Old code

::

    Epson = escpos.Escpos(0x04b8,0x0202,0)

New code

::

    Epson = printer.Usb(0x04b8,0x0202)

Nothe that "0" which is the interface number is no longer needed.